90-Degree HDMI Cable
Route digital video and audio around tight spaces with the BC-VHA009 90-Degree HDMI Cable range. Fixed-angle Type-A plugs route the cable beside or behind equipment, helping you avoid a sharp bend right after a straight connector.
- HDMI Type-A male-to-male audio/video connection.
- Single-angle and selected paired-angle configurations.
- Standard, slim, ultra-slim, and soft-jacket choices.
- Group-specific lengths from 0.15m to 2.5m.
- Up, down, and lateral exits matched to your port layout.
- OEM length, identification, and packaging review.
Choose the Exit Direction Before the Cable Profile
These angled HDMI leads carry digital video and audio between compatible sources and displays while guiding the cable through tight spaces. On wall-mounted screens, AV cabinets, and kiosks, the right exit direction can simplify routing and reduce the need to force a straight cable into a tight turn.
A shallow space behind a display involves more than cable length. The plug body, socket orientation, and first cable section must all fit without being pressed against the wall, bracket, or enclosure. The BC-VHA009 range offers fixed-angle Type-A plugs, so the cable can exit the socket in a direction that suits the actual equipment layout.
Choose a single angled end when one socket is constrained, or review the paired-angle standard references when both ends need a defined exit. Four jacket groups provide different cable profiles. They are mechanical choices, not a ranking of signal quality: the full housing and strain-relief envelope still need clearance, and the selected length must meet the intended AV requirement.
| Group | Listed jacket diameter | Catalogue lengths | Selection focus |
|---|---|---|---|
| Standard | 6.0mm | 0.15 / 0.6 / 1.8m | Molded plugs; single-angle and selected paired-angle combinations |
| Slim | 4.0mm | 0.3m | Short lead with reduced cable bulk; four single-angle references and a dimension illustration |
| Ultra-slim | 2.5mm | 0.6 / 1.2m | Pictured metal housings and PVC jacket; four single-angle references and a dimension illustration |
| Soft-jacket | 3.8mm | 1 / 1.5 / 2 / 2.5m | Listed silicone-jacket construction; housing material and exit geometry specified for the ordered configuration |
| Common requirement | What to define |
|---|---|
| Interfaces | HDMI Type-A male plugs at both ends; this range is not a female extension or an interface converter |
| Orientation | Socket mating-face view and cable exit at each end, including adjacent-port clearance |
| Performance | Resolution, refresh rate, color depth, chroma, HDR, gaming, audio-return and control functions for the exact model and length |
| Installation | Housing envelope, route length, cable support, and any environmental or continuous-motion requirements |
| Documentation | Ordered drawing and applicable test or certification records; no blanket rating is established for every pictured variant |
Send photos of both ports, the preferred reference, available depth, and target AV mode. We can review the connector geometry and sample requirements, along with your quantity and OEM needs, before releasing a bulk build.
Standard 6.0mm Angled HDMI Assemblies
The standard group lists molded housings, a 6.0mm PVC jacket, and lengths of 0.15, 0.6, or 1.8m. Four straight-to-angle references address one constrained socket, while six paired-angle references offer other routing arrangements. Match both ends to connector-face drawings. A shared jacket diameter does not qualify every model and length for the same AV mode.

P/N: BC-VHA009-SD60
This straight-to-down listing is a candidate when one equipment socket needs a vertical cable exit. Match the angled end to the installed port face and check the straight end separately. Select the required standard-group length with enough routing allowance for both strain reliefs.

P/N: BC-VHA009-SU60
The alternative vertical exit complements SD60 when the socket orientation or enclosure route faces the other way. Send an installed-port photo rather than relying on the word up. Confirm the male housing clears the equipment before selecting a 0.15, 0.6, or 1.8m standard lead.

P/N: BC-VHA009-SL60
A lateral angled end can redirect the route beside a crowded equipment socket. Check neighboring plugs and enclosure trim from the connector-face view. The other straight male end still needs room for its housing and a supported cable bend at the second device.

P/N: BC-VHA009-SR60
This opposite-lateral option provides another way to exit the constrained port. Compare the drawing with SL60 before ordering, especially when the socket is rotated in the equipment. Specify the standard-group length and target AV mode with the preferred reference.

P/N: BC-VHA009-UD60
The paired vertical-angle reference applies when both device connections need defined exits. Mark each endpoint separately on the layout; an up/down pair does not guarantee a particular turn after the sockets are installed. Review spacing, cable support, and full seating at both ends.

P/N: BC-VHA009-LR60
Opposite lateral angled plugs provide a different two-end route than straight-to-angle models. Check the cable exit at the source and display independently, including how each socket is mounted. A drawing showing both equipment faces helps avoid selecting the correct shape for only one end.

P/N: BC-VHA009-RR60
Two same-side lateral angled housings suit a route that requires matching plug geometry at both devices. Confirm each mating-face view and adjacent-port clearance before approving the reference. The same angle name at both ends does not alone determine the installed cable path.

P/N: BC-VHA009-LL60
This paired-angle option provides the opposite lateral geometry to RR60. Use it as a separate drawing-led choice, not a reversible substitute selected by name alone. Check both equipment sockets, the span between them, and the room available around the molded housings.

P/N: BC-VHA009-UU60
Two matching vertical-angle plugs provide defined exits at both ends of the connection. Compare each connector-face drawing with its installed socket, particularly when the equipment is mounted in different orientations. Include the standard-group length and device spacing so the cable can follow the route without pulling on either port.

P/N: BC-VHA009-DD60
The DD60 model provides an alternative matching vertical-angle pair to UU60. Check the cable exit at each device against its mating-face drawing and surrounding bracket. Choose this configuration when both exits match the planned route and you have sufficient cable length and support between the devices.
Slim 4.0mm Single-Angle HDMI Assemblies
The slim group lists a 4.0mm PVC jacket and a 0.3m lead. Choose from four angled male-plug exits when a short equipment link reduces cable bulk. The dimension card is a geometry reference, not another performance grade. Check the entire housing and collar against the equipment, not just the cable diameter.

P/N: BC-VHA009-SD40
The slim down-angle listing combines a short 0.3m link with the group’s nominal 4.0mm jacket. It can be reviewed where reduced cable bulk helps a local equipment connection. Check plug and collar clearance, since the jacket diameter is not the complete mounting envelope.

P/N: BC-VHA009-SU40
Choose the alternative vertical exit when SD40 points away from the available route. Confirm the port-face orientation and allow for the full 0.3 m lead-in in the equipment layout. A slim lead still needs to seat fully without the angled housing contacting the enclosure or neighboring connector.

P/N: BC-VHA009-SL40
The lateral slim option offers a short route beside the equipment. Include the installed socket orientation and adjacent plugs in the fit review. Select it for its mechanical arrangement, then verify the required video and audio functions on the exact 0.3m assembly.

P/N: BC-VHA009-SR40
Use this opposite lateral slim reference when SL40 doesn’t match the device layout. Compare the connector-face drawing and allow space for both male housings. The listed thin profile does not establish a universal display-bracket clearance or performance rating.

P/N: BC-VHA009-40
This card is the slim group’s connector-orientation dimension reference, not a separately validated cable model. Use it to discuss the required exit and housing envelope, then identify the actual ordered SD40, SU40, SL40, or SR40 assembly on the approved drawing.
Ultra-Slim 2.5mm Metal-Housing HDMI Assemblies
This group lists a 2.5mm PVC jacket, pictured metal housings, and 0.6 or 1.2m lengths. Four single-angle references and an orientation drawing support a compact-route inquiry. The metal body and thin jacket do not establish crush resistance, zero-gap display fit, or identical signal performance across all variants. Use the ordered drawing and sample.

P/N: BC-VHA009-SD25
The ultra-slim down-angle listing pairs a nominal 2.5mm jacket with pictured metal housings. Review the 0.6 m or 1.2m options for full-route and housing clearance. Reduced jacket bulk is a mechanical choice, not a guarantee that a display can sit flush against any bracket.

P/N: BC-VHA009-SU25
The alternative vertical-angle metal end offers another cable exit in the ultra-slim group. Check the device socket and enclosure trim from the mating-face view. Choose the required 0.6 or 1.2m length and evaluate that exact assembly at the intended AV settings.

P/N: BC-VHA009-SL25
This lateral metal-housing reference is useful to compare when the route runs beside the port. Confirm the dimensions of the angled body and the nominal 2.5mm jacket. Include the other device’s straight-plug clearance and the full cable route in the inquiry.

P/N: BC-VHA009-SR25
The opposite lateral reference complements SL25 for a different installed-port direction. Check the actual exit geometry rather than choosing based on the viewing angle in a product photo. Specify length, required picture format, and any audio-return or control functions with the part reference.

P/N: BC-VHA009-25
The ultra-slim dimension card provides orientation and housing references for build discussions. It is not an additional performance option. Confirm the exact ordered SD25, SU25, SL25, or SR25 drawing and its revision before using the dimensions to release an enclosure.
Soft-Jacket 3.8mm Angled HDMI Assemblies
The soft-jacket group offers a nominal 3.8mm silicone-jacket cable in 1, 1.5, 2, or 2.5m lengths. It gives you another routing option for local equipment connections. Specify the housing material and exit geometry with the selected model. For repeated movement, describe the motion and support arrangement so the required flex performance can be assessed separately from jacket softness.

P/N: BC-VHA009-SD38
The soft-jacket down-angle listing offers a longer local route than the 0.3m slim group. Review the listed 1, 1.5, 2, or 2.5m choices with both equipment positions. Specify the required jacket and housing construction on the order rather than assuming a flex-life rating.

P/N: BC-VHA009-SU38
Review this alternative vertical exit when BC-VHA009-SD38 doesn’t suit the installed socket direction. Check the housing and route before selecting a length from the soft-jacket group. Softness alone doesn’t allow repeated motion, tight folding, or a specific minimum bend radius.

P/N: BC-VHA009-SL38
The lateral soft-jacket option is a candidate where a sideways exit fits the equipment layout. Confirm the actual connector-face geometry, housing material, and cable length in the quotation. For a moving or frequently handled assembly, provide the motion and service requirements for separate review.

P/N: BC-VHA009-SR38
This opposite lateral reference offers an alternative route to SL38. Match it to the installed port and available cable-support points before sample approval. Include the selected length and AV mode, since one working configuration does not qualify for every soft-jacket variant.
Define the Required Picture, Audio and Control Functions
Use an angled lead to carry digital video and audio to a screen when rear or side clearance is limited. The connector redirects the route while keeping a single HDMI connection, so the installation stays compact without adding a separate right-angle adapter. Select the exact model and length for the required resolution, refresh rate, and color format; 8K60, 4K120, HDR, and gaming features depend on the approved assembly and compatible equipment.


Check the Housing Against the Real Clearance
A fixed-angle plug turns the cable exit at the connector, helping you work around a wall bracket, enclosure edge, or neighboring port. This can make a shallow display installation easier to arrange and reduce bending immediately behind the plug. Match the exit to the socket mating-face view and allow enough room for the housing to seat fully. Support the cable so the equipment socket does not carry its weight.
Approve the Selected AV Configuration
Choose the required model and length, then check the intended video, audio, and control settings on the actual equipment. Include normal startup and power cycling, and repeat the agreed checks after routing. An angle alone does not add latency or improve gaming performance; results depend on the complete, compatible setup. Request applicable evidence for any performance or certification requirement.


Compare Cable Profiles Without Confusing Them With Ratings
The 6.0 mm, 4.0 mm, 2.5 mm, and 3.8 mm groups provide different mechanical profiles and listed lengths. Measure the full plug body rather than using the jacket diameter as the required clearance. A thin cable is not automatically a higher-bandwidth cable, and a soft jacket does not automatically qualify as continuous-flex. Confirm the ordered materials and route requirements separately.
Turn the Layout Into an OEM Specification
Send both connector-face orientations, finished length, housing limits, jacket requirements, and quantity. Include any labeling, packaging, or compliance documentation needed for the project. The cutaway illustration is a discussion aid, not material verification for every pictured model. Agree on the drawing, sample acceptance, and commercial terms so later bulk orders repeat the approved build.


Plan the Equipment Connection, Not Just the Visible Bend
Connect a media player behind a digital signage screen, route a lead inside an AV cabinet, or fit a display connection into a kiosk. These are practical uses for a defined cable exit and a choice of jacket profiles. With a compatible computer, the connection can carry a mirrored presentation or an extended desktop, along with digital audio. Choose both port orientations and the required video mode before settling on a model.
The pictured BC-VHA009 cable references have male Type-A HDMI plugs at both ends. They are not female-ended extensions or panel couplers. Identify the equipment sockets and any other required adapters before choosing the assembly.
No. These are fixed-angle plugs, not swivel connectors. Choose the exit direction before installation. If the cable points toward a bracket or a neighboring port, choose a different angle instead of twisting the housing or leaving the plug partially inserted.
No locking feature is established by the standard plugs shown. Seat them fully without force and support the cable. If retention is necessary, specify hardware designed for the actual equipment rather than treating an angle as a lock.
An angled connector or PVC/silicone description does not establish weather sealing, an IP rating, or an in-wall fire classification. Specify the environment and required documentation for the exact assembly before using it in a protected or concealed installation.
No. These male-to-male HDMI leads do not change the interface. A different source or display connection needs an appropriate adapter or converter with the correct direction and capabilities, as included in the full system review.
No. Housing material and contact finish are different specifications from signal performance and certification. Request the applicable records for the exact cable model and length if a certified category or material requirement is part of your acceptance criteria.
These are finished assemblies, not field-termination or re-forming kits. Do not cut, reterminate, or heat-bend them without an approved method for the exact construction. Request the required finished geometry and length for review instead.
Look straight at the equipment socket’s mating face and mark where the cable needs to go. Include the surrounding bracket and neighboring ports in the photo. Match that view to the chosen connector drawing, and repeat the check at the other end for a paired-angle cable. Direction names alone can be misleading when a device is mounted vertically or upside down.
Related Products
How to Specify an Angled HDMI Cable Without Guessing the Exit Direction
“I need a right-angle HDMI cable” is a useful starting point, but it is not yet a complete specification. The same socket may be installed horizontally, vertically, or upside down in different equipment. A plug that sends the cable towards free space on one display may send it straight into the bracket on another. Defining the view and both endpoints makes the request checkable before ordering a cable.
Start with a photo of each installed socket
Take a clear view of the connector face and a wider view showing the wall, bracket, shelf, or enclosure. Identify the equipment and port number. Mark the cable exit direction and the available space around the socket. If the equipment is not yet built, provide the connector location and enclosure drawing instead.
Do this for both ends, even if only one will be angled. The straight end also needs clearance for its body, collar, and a supported bend. If both ends are constrained, identify the source and display separately so the paired-angle reference can be checked against the actual layout.
Keep three different measurements separate
Jacket diameter describes the cable, not the plug. A 2.5mm cable can still have a housing that collides with nearby hardware. Connector-body dimensions describe the rigid envelope, while the collar and cable route add a third space requirement. Measure all three rather than assuming that the thinnest listed cable must fit the shallowest installation.
| Layout question | Information to send |
|---|---|
| Which way must the cable leave? | Mating-face view with a marked exit at each endpoint |
| Will the housing seat fully? | Socket recess, available depth, and adjacent-port dimensions |
| Where will the first bend sit? | Collar clearance, support location, and route space |
| How much cable is needed? | Measured installed route, service allowance, and finished-length definition |
| What must the link carry? | Endpoint models and complete video, audio, and control requirements |
Choose one angled end or a paired-angle reference
The standard group includes four straight-to-angle references and six paired-angle references. A single angled end can solve a local exit problem without imposing an angle on the other equipment socket. A paired model can define both exits, but both drawings must be correct. Turning the cable around is not a substitute for checking how each plug mates with the actual installed socket.
UU60 and DD60 offer alternative matching vertical-angle pairs. Compare their connector-face drawings with both installed sockets; the same plug geometry can point in a different room direction when you rotate a device. The slim and ultra-slim dimension cards help you check the housing envelope of the selected model.
Select a profile around the route
The standard group lists a 6.0mm PVC jacket and several short lengths. The slim group uses a listed 4.0mm jacket and a 0.3m lead for a short local connection. The ultra-slim group lists a 2.5mm jacket, metal housings, and 0.6 or 1.2m choices. The 3.8mm soft-jacket group offers longer listed local lengths and is described as silicone-jacket construction.
These profiles help frame a mechanical inquiry. They do not establish a universal bend radius, crush resistance, continuous-motion life, or identical signal performance. Specify the soft-series housing material and jacket construction in the quotation. If motion or frequent handling matters, provide the movement, support, and service requirements for review rather than relying on “soft” as a test rating.
Specify performance by model, length, and required mode
An angled plug is a geometry choice. It does not increase frame rate, reduce game latency, or add a video feature to the source or display. Identify the resolution and refresh rate together with color depth, chroma, HDR, and any compression conditions. Add the required audio formats, ARC or eARC return-audio path, CEC, VRR or ALLM requirements where relevant.
The official HDMI cable guide distinguishes cable categories and certification programs. Request documentation for the exact assembly and length when a certified category is required. A product image with an 8K marking or a connector version description is not a substitute for that evidence, and HDCP is not a cable certification category.
Fit and test the sample before closing the enclosure
- Confirm both exit views, part reference, and finished length against the layout.
- Align and seat each plug fully without forcing the housing against nearby hardware.
- Support the route so neither socket carries a sideways cable load.
- Check the required picture settings and audio/control functions on the intended equipment.
- Repeat relevant checks during normal startup and power cycling and after final routing.
- Record the accepted cable, endpoints, and settings for the bulk build.
If a new connection is intermittent, compare with a known-good direct lead and inspect seating before changing settings or adding adapters. Do not leave a plug partly inserted to avoid a housing collision. A cable can have the correct interface and still be the wrong mechanical fit for a particular enclosure.
Use another architecture when the installation needs it
For a fixed external service point with mounting hardware, compare the HDMI panel-mount cable options. For longer routes, review the fiber optic HDMI range against your full AV requirements. An angled copper lead solves an exit problem; it is not a universal substitute for a mounting assembly or a long-distance architecture.
Send both port photos, preferred BC-VHA009 reference, route length, and target AV mode with your quantity. Add drawing, identification, and packaging requirements for an OEM build. BespokeCable can review the geometry and sample proposal based on those details before releasing the order.



















