90° Ethernet Cables for Fixed RJ45 Routing in Tight Spaces
Route an Ethernet connection beside a cover, wall, or equipment edge with one fixed molded RJ45 bend and one straight plug. The BC-DAJ015 family combines four angle references with black or white cable, helping define a repeatable assembly for the installed port layout.
- BC-DAJ015 RJ45 male-to-male patch cables with one straight and one molded 90-degree connector.
- Eight listed combinations: up, down, left, or right angle in black or white.
- Listed lengths of 0.5m, 1m, 1.5m, 2m, 3m, 5m, 8m, and 10m; confirm the required version when ordering.
- Listed 6.0mm cable profile; confirm conductor, shielding, and jacket details for the selected assembly.
- Choose the bend against your port orientation, adjacent connectors, and cover clearance.
- Send the required link speed, PoE load, length, and quantity for a configuration-specific quote.
Choose the Angle Before Choosing the Length
A straight RJ45 plug can fit the socket yet leave too little space for the cable behind it. A molded 90-degree Ethernet cable changes the cable exit at the connector, helping installers route a connection around a cover, wall, or equipment edge without forcing a sharp bend into the jacket.
The BespokeCable BC-DAJ015 family combines a straight RJ45 male connector with an angled RJ45 male connector. Four angle references and two colors provide eight starting configurations. Please share a photo of the port and the available clearance so we can confirm the best fit for your installation.
Ordering Specifications
| Item | Configuration reference |
|---|---|
| Family | BC-DAJ015 90-degree Ethernet patch cables |
| Connection | RJ45 male to RJ45 male; straight-to-angle arrangement |
| Angle options | Up, down, left, and right as identified by the model drawing |
| Colors | Black and white |
| Listed lengths | 0.5m, 1m, 1.5m, 2m, 3m, 5m, 8m and 10m; confirm availability |
| Listed cable profile | 6.0mm diameter; confirm the selected drawing and tolerance |
| Category selection | Cat6-labeled family; agree on finished-assembly and channel performance requirements |
| Conductors and shielding | Confirm gauge, material, cable shield, and shield termination for the ordered version |
| Jacket and environment | Confirm material and installation requirements; no outdoor or ingress rating is implied |
| PoE | Review equipment, load, length, and installation conditions before approval |
Eight Model References
| Angle reference | Black | White |
|---|---|---|
| Up | BC-DAJ015-UB | BC-DAJ015-UW |
| Down | BC-DAJ015-DB | BC-DAJ015-DW |
| Left | BC-DAJ015-LB | BC-DAJ015-LW |
| Right | BC-DAJ015-RB | BC-DAJ015-RW |
Angle names are not universal installation directions. The same connector can point differently when you rotate the device socket. Use the latch position and the model image as your reference, and mark the required cable exit on a photograph before ordering.
Check the Space Around the Port
The angled body can reduce the straight run needed behind a socket, but it may occupy space beside it. Check neighboring ports, power connectors, rack rails, and the path of a closing door. Leave enough room to release the RJ45 latch; an assembly that cannot be unplugged conveniently may create a maintenance problem even if it fits.
The molded angle is fixed. It is not a swivel joint and should not be twisted to obtain another direction. Support the cable so the connector does not carry its weight, and allow a natural bend beyond the strain relief. For more connector combinations and smaller cable profiles, compare the slim Ethernet cable range.
Define Performance Separately from the Angle
A 90-degree connector changes routing, not the network protocol. It does not increase data rate, act as a repeater, or establish PoE capacity. Confirm the required link speed based on the final length and complete channel arrangement. Generic Cat6 distance figures are not a test report for every version in this family.
Metal connector shells do not by themselves establish a shielded cable system. Where shielding matters, specify the cable construction, termination, and equipment connection together. Where PoE is required, provide the powered-device demand and operating conditions so conductor resistance and power delivery can be considered. These details belong on the order specification, not in assumptions based on a photograph.
Custom Cable Planning and Sample Approval
For OEM equipment or repeat installations, provide a drawing showing both ports, the connector envelope, finished length, and required labels. Black and white can support your own identification scheme, but color does not indicate a different electrical function. We review additional customization against the required construction and quantity.
Approve a sample with the actual neighboring connections installed. Check fit, latch access, and the agreed electrical requirements before releasing a larger order. If a straight assembly already fits the route, our standard patch cable options may offer a simpler solution. Send the model reference, quantity, and installation details for a quote suited to your project.
Request a 90-degree Ethernet cable quotation with your angle references, lengths, quantities, and port drawings.
Similar Products Show & Comparison of 90-Degree Ethernet Cable
Compare the eight BC-DAJ015 angle-and-color combinations below. Confirm direction against the port latch and the product drawing; the two dimension illustrations are reference material, not additional cable models. Confirm link performance and PoE suitability separately for the selected assembly.

P/N: BC-DAJ015-UB
Black up angle Ethernet cable pairs one molded RJ45 bend with a straight male plug for a compact equipment route. Match the up reference to the installed socket latch before setting the path. Check the required length, neighboring connectors, and accessible latch release.

P/N: BC-DAJ015-DB
Black straight-to-down-angle Ethernet cable option for a defined cable exit near the equipment port. Confirm the actual socket orientation and available latch access. The fixed molded bend should match the route without twisting the connector or pressing it against a cover.

P/N: BC-DAJ015-LB
Black straight-to-left-angle Ethernet cable option. Compare the connector drawing with the installed port rather than assuming left means the same from every viewpoint. Check adjacent sockets and cable support, then confirm the finished length and electrical requirements for the order.

P/N: BC-DAJ015-RB
Black straight-to-right-angle Ethernet cable option for a drawing-defined side exit. Provide a port photograph with nearby connections visible so the connector envelope can be reviewed. Choose this version for fit, while specifying network speed and power requirements separately from the angle.

P/N: BC-DAJ015-UW
White straight-to-up-angle Ethernet cable option for installations using a light-colored cable scheme. Confirm the exit direction against the model drawing and port latch. Match the assembly length and connector clearance to the route before approving the selected construction for production.

P/N: BC-DAJ015-DW
White straight-to-down-angle Ethernet cable option. Review it with the equipment in its final mounting position, leaving room for latch release and cable support. White identifies the selected cable appearance; data performance, conductor construction, and PoE suitability still require configuration-specific confirmation.

P/N: BC-DAJ015-LW
White straight-to-left-angle Ethernet cable option for a defined side-routing layout. Check the socket orientation, adjacent port spacing, and any nearby cover. Include a marked port photograph with your inquiry so the direction can be reviewed before the cable is ordered.

P/N: BC-DAJ015-RW
White straight-to-right-angle Ethernet cable option. Select it against the product drawing and the installed port, allowing room for neighboring plugs and maintenance. Confirm the finished length, construction, and acceptance requirements together so repeat orders follow the same approved assembly specification.

Left/right connector dimension reference for BC-DAJ015. Confirm the current drawing for the selected LB, RB, LW, or RW version before designing the installation space. This is a reference chart, not a separate cable model.

Up/down connector dimension reference for BC-DAJ015. Check the current drawing for the selected UB, DB, UW, or DW version, including latch clearance and strain relief. Confirm tolerances before committing to a tight enclosure opening.
Confirm the Exit Direction in the Installed Position
The BC-DAJ015-UB image illustrates a fixed-angle connector paired with a straight RJ45 plug. The exit orientation depends on the socket, so use a port photo with the latch visible to confirm the fit.
Measure the space for the whole housing, not just the cable. Leave access for unplugging and check nearby ports with their cables fitted. A clear fit reference helps avoid ordering an angle that clears one obstacle but blocks another.

Confirm the connector direction before insertion, align the plug without force, and check that the latch engages. Support the cable without twisting the angled body or pinching the jacket. Verify clearance with neighboring ports populated, and test the required network operation after installation.
It is an Ethernet cable with a connector housing that turns the cable exit by 90 degrees. This family has one straight RJ45 male end and one angled male end. The angle addresses physical routing; it does not change the network protocol.
They use different cable-exit directions relative to the connector drawing. The installed direction also depends on the socket orientation. Send a port photo with the latch visible and mark your required exit; do not select by the word “left” or “right” alone.
An angled assembly can meet a defined Ethernet application, but you must establish its performance for the selected construction and length. The housing shape alone neither improves nor proves data performance. Agree on the required link and test criteria before approval.
Choose the reference whose drawing matches the required exit at the installed socket. The latch position, adjacent plugs, and nearby covers determine the practical direction. Rotating the equipment or socket changes how an up or down reference routes, so confirm it with the port view.
Listed length options are 0.5m, 1m, 1.5m, 2m, 3m, 5m, 8m, and 10m, in black or white. Confirm availability for the selected angle and construction. We can review custom requirements based on your quantity and application.
PoE suitability must be confirmed for the selected cable and load. Provide the source equipment, powered-device demand, length, and installation conditions. An angled plug does not determine power capacity; conductor size and resistance must match the application.
The family lists a 6.0mm cable diameter. Confirm the selected assembly drawing and tolerance before designing a clamp or cable opening. The connector body and strain relief need separate clearance.
Send the required connector arrangement, finished length, color, labels, and quantity for review. Customization is confirmed based on feasibility and electrical requirements; it is not limited to changing the appearance of a standard assembly.
We quote the MOQ and lead time for the chosen model and customization. Provide the quantity and project schedule in your inquiry. Different materials, colors, or labeling requirements can affect the order conditions.
Measure the supported cable route plus service allowance, not only the straight-line distance between ports. Check the complete connector envelope and latch access. State the finished-length measurement reference on the order.
The practical value includes four angle references in black or white, plus a configuration review for your installation. BespokeCable can discuss port clearance, length, and identification requirements so we can document the selected assembly for repeat orders.
Identify the two ports, mark the required exit direction, measure the available space, and define the length. Then specify the required data rate, PoE load, and environment. Confirm the drawing and sample fit before approving the quantity order.
How to Specify the Correct 90-Degree RJ45 Cable
The wrong-angled cable often looks right until you plug it in. Left and right depend on your viewing direction, and a socket mounted upside down reverses how a familiar connector appears to route. A clear mechanical reference prevents this avoidable mistake.
Describe the cable exit on a port photograph
Take a photograph square to the port face. Show the latch recess and mark the direction in which the cable should leave the socket. Include the surrounding connectors and the nearest obstruction. This is more useful than asking for a left-angle cable without showing how the equipment is mounted.
Identify which end needs the angle. Assess a straight-to-angle cable at both ends, even if only one port has a clearance problem. If the straight end also requires a sharp forced bend, the route or connector combination needs another review.
Measure the connector envelope
Do not measure only the cable diameter or the gap behind the device. The plug body, angled housing, and strain relief all occupy space. Compare the required clearance with the selected model drawing, including the room needed to operate the latch.
A useful fit check includes adjacent ports populated and covers closed. A connector may clear the wall but overlap the next socket, or fit beneath a cover while trapping its release tab. Don’t rely on panel pressure to hold the cable in place.
Route the cable without turning the plug into a lever
The molded angle is intended to establish a fixed exit direction. Pulling the cable sideways or twisting the connector to correct the route can load the equipment socket. Support the cable beyond the connector and allow a natural bend in the jacket. A right-angle connector does not remove the need for bend clearance elsewhere in the route.
Plan enough service allowance to disconnect the equipment. If a device must slide out of a rack or move during maintenance, include that movement in the length decision. Repeated operating motion requires a separately specified cable duty; it is not implied by an angled plug.
Write the electrical requirement into the same order
Once the physical fit is clear, record the required data rate, length, and complete channel arrangement. Do not use the connector angle as a performance category. A short bench link and the final installed connection can differ, especially when couplers or permanent cabling are involved.
For PoE, identify the source equipment and powered-device demand. Confirm the conductor construction and operating environment appropriate to that load. If shielding is required, specify the complete shield path rather than relying on a metal connector shell as proof. Agree which inspection or test results will be used for acceptance.
Approve the sample and control repeat orders
Keep a record of the approved model, orientation drawing, length reference, and any label requirements. Test the sample in the intended equipment arrangement and note any change before production. A photograph of the accepted installation can help later purchasing teams avoid substituting a visually similar but differently oriented cable.
For multiple locations, use a cable schedule with endpoint names, quantities, and colors. Color is for identification, not a performance guarantee. Confirm packing and order conditions in the quotation so the delivered assemblies can be assigned to the correct installation without guesswork.
Send BespokeCable the port photographs, measured clearance, and cable schedule. We can review the BC-DAJ015 angle reference with your team and help turn the space constraint into an orderable assembly specification.
Send your fixed-angle Ethernet cable schedule with endpoint photographs and clearance dimensions for review.














