eSATA Bracket
Make an existing supported SATA connection accessible at the rear of a computer case. BC-DAH005 is a passive eSATA slot-plate bracket with integrated internal data leads, offered in single- and dual-port references.
- A: one external eSATA receptacle and one internal SATA data lead.
- B: two external eSATA receptacles and two separate internal SATA data leads.
- Internal plugs have visible metal latches in the reference photos.
- Uses the chassis expansion-slot cover position mechanically; no PCIe edge connector or controller is shown.
- Data only: external storage requires its own appropriate power supply.
- Confirm case fit, lead lengths, available host ports, and complete-route performance before ordering.
Product Details
Opening the computer case every time you need an external storage connection is inconvenient. The BC-DAH005 eSATA bracket brings an existing supported SATA data path to a secured rear-panel position, with one or two external receptacles and integrated internal leads.
The bracket is a passive connection assembly, not a PCIe controller card. It does not add a SATA channel, upgrade an older controller, or power an external drive. Start with the host ports you actually have, then check the case opening and complete cable routing.
Single Port or Two Independent Ports
| Model | Reference configuration |
|---|---|
| BC-DAH005-A | One external eSATA receptacle; one integrated internal SATA data lead |
| BC-DAH005-B | Two external eSATA receptacles; two integrated internal SATA data leads |
Each external port needs its own available, supported SATA host connection. B is not a splitter that turns one motherboard port into two. The photos show red leads already attached to the port assemblies, ending in latched internal SATA cable sockets; they are not simply bare rear connectors that always require another pair of separately purchased data leads.
Connection and Mechanical Specification
| Item | Selection basis |
|---|---|
| External interface | Standard data-only eSATA receptacle, one per path |
| Internal connection | Integrated seven-contact SATA data cable socket per path, with visible metal latch |
| Mounting | Metal slot-cover plate for a compatible chassis opening; no PCIe electrical connection |
| Power | No drive-power connection or powered eSATA supply provided |
| Link capability | Depends on host/controller, storage, and complete passive route; no SATA-generation upgrade |
| Case fit | Reference drawing labels 120mm and 18.5mm bracket dimensions; compare full outline and retention details |
| Lead length | Specify required internal reach and measurement points for the ordered model |
| Hardware and materials | Confirm exact finish/material, fasteners, packing, and required documentation in the quotation |
Check the Host Before the Case Opening
The internal leads connect to compatible SATA host ports on the motherboard or controller. Confirm that the ports are available and enabled, including any sharing restrictions with other motherboard interfaces. A spare expansion-slot cover does not establish an available SATA channel.
The bracket uses that cover position only for mechanical access. It has no pictured PCIe edge connector or controller chip. It cannot turn SATA I into SATA II, create RAID functionality, or make an unsupported port suitable for every external enclosure. A controller upgrade is a different product decision.
Review the Complete Data Path
The intended link rate must be checked against the actual host, external storage, and full connection. SATA generations commonly use nominal 1.5Gbps, 3Gbps, or 6Gbps rates; the slowest supported configuration and signal route remain limiting factors. These are bits per second, not a promise of 3GB/s or 6GB/s file transfers.
Include the internal bracket lead, rear connector, and external cable in one route. Passive pass-through hardware does not regenerate the signal or automatically provide the electrical conditions of a native external eSATA controller. Do not assume that a general 2m external-cable figure applies unchanged after adding an internal lead and bracket.
For an existing native eSATA connection, a standard eSATA data cable may be sufficient. For a USB-only host, review the active USB-to-eSATA bridge options rather than expecting this passive bracket to add a controller.
Match the Plate and Cable Reach to the Chassis
The dual-port reference drawing shows a 120mm plate dimension and 18.5mm side reference. Compare the full outline, mounting tab, retention point, port clearance, and neighboring hardware with your case. Don’t assume the pictured plate fits every low-profile, small-form-factor, or proprietary chassis.
Measure each internal route to the chosen host port and leave room to release the metal SATA latch. Keep the leads away from fans, sharp edges, and covers that could pinch them. Confirm the exact included fasteners; screws visible at the port bodies are not proof that a chassis thumb screw is supplied.
Keep External Storage Power Separate
The pictured assemblies expose only standard eSATA data ports. No SATA power connector, LP4 lead, USB power branch, or powered-eSATA contacts are specified. Use the external enclosure’s approved supply. If you need a different source-matched power arrangement, compare the eSATAp cable layouts rather than treating this bracket as a power source.
Prepare a Useful OEM Inquiry
Send the motherboard/controller and chassis models, required port count, internal route lengths, rear-opening dimensions, and external storage details. Include order volume, labels, packing, and documentation needs. BespokeCable can review the bracket assembly and sample specifications with you. Confirm the approved drawing, hardware list, complete-system validation scope, and commercial terms before repeat production.
Choose One Port or Two Independent Paths
Select the number of external data connections and confirm a separate available SATA host port for each. Both pictured assemblies include internal red data leads; neither is a controller card or a source of drive power.

P/N: BC-DAH005-A
The single-port reference provides one rear eSATA receptacle with one integrated, latched SATA data lead. Choose it for a defined host-to-external-storage path. Confirm chassis plate fit, cable reach, and host support; the bracket adds no controller channel and does not supply power to the external device.

P/N: BC-DAH005-B
The dual-port reference groups two independent eSATA data connections on one plate, with two internal SATA leads. It needs two suitable host ports, not one split connection. Before approving the sample for a two-path storage setup, check both lead routes, rear-panel clearance, and external-device power.
Two Rear Receptacles, Two Internal Data Leads
The B-model image shows two eSATA receptacles on a metal plate and two red internal leads ending in latched SATA cable sockets. Each cable represents a separate data path back to a compatible host port.
Secure the bracket at the case’s slot-cover position; do not plug it into the PCIe bus. Check the plate outline and both internal routes, and provide power to the external storage separately.

No. The pictured bracket uses the chassis expansion-slot cover position mechanically. It has no PCIe edge connector or controller shown. Its internal SATA leads use existing supported host ports.
Two separate supported SATA host ports are needed for two independent paths. The bracket is not a port splitter, hub, or controller that expands one SATA port into two.
Yes, the A and B reference photos show one and two integrated red SATA data leads, respectively, with latched cable sockets at the internal ends. Confirm the exact length and assembly revision in the order rather than assuming that extra separate leads are always required.
No. These are standard eSATA data paths. The external enclosure or device needs its own suitable, approved power supply. These assemblies show no SATA power, LP4, or USB power branch.
No. A passive bracket does not change the controller generation. SATA link rates are commonly expressed as 1.5, 3, or 6Gbps, not 3GB/s or 6GB/s file-transfer guarantees. Confirm the rate supported by the host, storage, and the complete route.
No. Compare the full outline, tab, retention method, port clearance, and internal space with your chassis. The reference drawing labels the 120 mm and 18.5mm bracket dimensions; do not assume a low-profile or proprietary case accepts the pictured plate.
Do not assume so. The integrated internal lead, rear connector, and external cable form one passive path. Host signal capability and added connection loss matter. Evaluate the complete sample against the intended equipment configuration.
No. The controller, firmware, operating system, and storage device must support the intended behavior. Follow their connection sequence and safely eject or unmount storage before disconnecting when required.
Confirm the model-specific internal lead length, measurement points, and packing list in the quotation. The port-body screws in the photo do not indicate that a chassis thumb screw is included. Use retention hardware appropriate for the actual case.
Provide chassis and motherboard/controller models, port count, internal route lengths, external storage and cable details, quantity, and any labels or packaging needs. Include required validation and documentation. Confirm sample terms, minimum quantity, hardware, and lead time for the agreed assembly.
Planning a Passive eSATA Bracket Installation
A tidy rear-panel connection begins with a supported host path, not merely an empty opening in the case. Use the sample to verify mechanical installation and storage operation in one setup.
Reserve the Required SATA Ports
For a single-port bracket, identify one supported internal SATA host port. For the dual-port model, identify two. Check the motherboard documentation for disabled or shared ports when other devices are installed. Record which rear receptacle maps to which host connector for service and repeat builds.
Check the Case Retention Details
Compare the bracket outline and mounting tab with the chassis, including full-height versus low-profile requirements. Follow the computer manufacturer’s power-isolation and case-opening instructions. Use the correct case retention hardware; do not assume a particular thumb screw or thread is included without the agreed packing list.
Route the Integrated Leads
The photos show leads already attached to the bracket port assemblies. Measure their reach to the selected host connectors and confirm any required custom length. Avoid fan paths, pinched covers, and tension at the motherboard socket. Leave access to the release tabs rather than routing the cable so you can’t service it without pulling on the wire.
Evaluate the Entire Signal Route
Connect the intended external cable and powered storage device as part of sample evaluation. The internal lead and additional connectors are part of the same path. Define the required negotiated rate and workload checks; a passive bracket does not condition the signal or upgrade the controller.
Follow the System’s Hot-Plug Rules
Hot-plug behavior depends on the controller, firmware, operating system, and storage device. Follow their instructions and safely unmount or eject storage before disconnection when required. If a drive containing wanted data is not recognized, check power, port support, and known-good equipment before changing disk settings; do not format it as a connection test.
Control the Production Assembly
Keep the model, plate drawing, internal lengths, port map, materials, and fastener list attached to the purchasing specification. Agree on any continuity, mechanical-fit, and system data-link verification, and request the records your project needs. Confirm sample charges, minimum quantity, and delivery timing for the actual order.
Send the chassis details and route sketch through the inquiry form. If the problem is a mismatched data connector rather than a fixed panel position, compare the eSATA-to-SATA data adapters before choosing the assembly.









