SATA Data, Power and Combined Connector Formats
BespokeCable supplies 7-pin, 13-pin, 15-pin, and 22-pin SATA connector configurations for OEM boards, storage devices, and cable assemblies. The current cards distinguish data, power, and combined contact arrangements. Each must still be specified by connector gender, PCB or cable side, orientation, footprint, mating component, and system use.
A 7-pin format is commonly used for SATA data, and a 15-pin format for power, while combined formats integrate functions into a single mating interface. However, pin count alone does not define the full production specification. Provide the exact connector drawing, equipment mate, and contact assignment, especially for compact or application-specific 13-pin arrangements.
Connector capability should not be separated from the full channel. Data performance depends on the board, mate, cable, and layout; power behavior depends on the host, device, rails, current, and sequencing. State required validation and evidence for the finished system rather than applying universal speed, voltage, hot-swap, or mating-life claims to every card.
Send the mating device and board or cable drawing for review.
SATA Connector Formats

This 7-pin SATA connector configuration represents the data-side interface. Confirm whether the part is PCB- or cable-side, plug or receptacle, straight or right-angle, and the exact footprint and mating. Channel performance still depends on the complete board, cable, and system implementation.

This 13-pin SATA connector configuration combines an interface used in a compact, equipment-specific arrangement. Confirm the exact contact layout, mating, intended data and power assignments, board or cable use, orientation, keying, and footprint. Do not assume a universal pin map from the count alone.

This 15-pin SATA connector configuration represents the power-side interface. Define plug or receptacle, PCB or cable use, straight or right-angle orientation, mating device, contact assignment, board footprint, and electrical design. Voltage rails and sequencing must follow the host and device specifications.

This 22-pin SATA connector configuration combines the common data and power contact groups into a single mating arrangement. Confirm the connector gender, device or board use, orientation, footprint, keying, and exact pin assignments. Hot-plug behavior and data performance require system-level validation.
Separate Data, Power and Combined Interfaces
Identify whether the connector carries data, power, or both, and provide the exact contact assignment. A 7-, 15-, 13-, or 22-pin label narrows the format but doesn’t define the full part, gender, orientation, or equipment use.


Define the Connector Side and Orientation
State PCB or cable mounting, plug or receptacle, straight or right-angle orientation, and mating direction. Include the device, board, and enclosure drawings so the key, insertion path, connector height, and latch clearance can be checked together.
Use the Approved Footprint and Mechanical Drawing
Provide the terminal layout, mounting posts, board thickness, keep-outs, and enclosure distance. Similar SATA faces can use different board geometry. Select and validate the exact part rather than copying a generic footprint.


Validate Data and Power at System Level
The connector is one element of the SATA channel and power path. Define the required system generation, board and cable implementation, rails, current, grounding, and any sequencing or hot-plug requirements. Test the representative assembly instead of assigning performance from the shell alone.
Control Sourcing and First-Article Approval
Check the real mate, board fit, keying, insertion, retention, and termination on a sample. Freeze the part, drawing, source, and inspection criteria. Any alternate should be compared and approved under the project quality plan.

They are commonly used for different functions: the 7-position format for data and the 15-position format for power. The exact part still requires specifications for gender, mounting, orientation, mate, and equipment.
It is a combined contact arrangement that brings common data and power groups into one mating interface. Confirm the exact device or board side, gender, orientation, footprint, and contact assignment before selection.
Do not assume so. Provide the exact equipment documentation, mate, and contact map for a compact or application-specific 13-position format. Verify the sample in the intended system.
Not a drop-in change. The mating direction, PCB footprint, connector height, rear space, and enclosure path differ. Review the board and mechanical design before changing orientation.
No. Performance depends on the full channel, including board layout, mating, cable, and system implementation. State the target generation and validate a representative path.
No. Hot-plug behavior depends on the host, device, contact sequencing, power design, controller, and software. Define the system requirements and validate them beyond the connector component.
The approved connector drawing should be used for the footprint and mechanical layout. First, identify the exact part, then verify the land or hole pattern, mounting features, and keep-outs against the board design.
Yes, when you provide the exact interfaces, cable construction, length, orientation, and system requirements. Treat the connector components and finished cable assembly as separate controlled items in the documentation.
Compare mate, keying, dimensions, footprint, contacts, materials, and evidence. Sample the alternate in the actual board or cable assembly and perform the agreed system checks before adding it to the approved list.
No verified child detail pages were found for the four live connector configurations. The inquiry pop-up lets the buyer send the exact mate, board, and system requirements, while Product Link remains blank instead of pointing to an unrelated page.
How to Specify a SATA Connector
SATA connector selection begins with the equipment architecture: a data interface, a power interface, or a combined device connection. Pin count is a useful first filter, but production release requires the exact mating side, orientation, board or cable implementation, and system validation.
1. Identify the Function
State whether the connector carries SATA data, device power, or both. For an application-specific compact format, provide the equipment documentation and exact contact map. Do not infer unused contacts, voltage rails, or signal assignments only from the total number of positions.
2. Define the Mating Side
Identify plug or receptacle, host or device side, and the exact mating part. Provide a drawing or sample. Confirm key geometry and insertion direction so the connector cannot be selected from a mirrored photograph or the wrong viewing side.
3. Choose PCB or Cable Implementation
State whether the product mounts to a PCB, terminates a cable, or forms part of a combined assembly. For PCB connectors, provide footprint, board thickness, orientation, mounting posts, and keep-out space. For cable-side parts, define cable construction and strain relief separately.
4. Check Straight or Right-Angle Geometry
Confirm mating direction, connector height, rear depth, latch or friction-retention access, and enclosure clearance. A right-angle part is not a drop-in substitute for a straight part because the footprint and mechanical path differ.
5. Define the Data Channel Requirement
State the target system generation and the complete board, cable, and mate configuration. Signal integrity depends on the full path, not only the connector. Use system-specific design and validation criteria rather than a universal speed statement for every component.
6. Define the Power Path
Provide the host and device power requirements, voltage rails, current, grounding, and contact assignment. Any sequencing or hot-plug behavior belongs to the complete system design. Reconcile the connector drawing and equipment specification before release.
7. Review Materials and Evidence
Control contact, plating, housing, temperature, and compliance requirements by exact part data where needed. List required documents in the RFQ. A material statement for one component does not certify an assembled board, cable, or storage system.
8. Approve the Representative Assembly
Verify mating, keying, board or cable fit, retention, and termination. Conduct the required data, power, and functional checks in the actual equipment or an agreed representative setup. Freeze the approved part and alternate policy for repeat orders.
SATA Connector RFQ Checklist
| Area | Required input |
|---|---|
| Format | 7, 13, 15, or 22 positions and data, power, or combined function |
| Mate | Plug or receptacle, host or device, and exact mating part |
| Mechanical | PCB or cable use, orientation, footprint, and enclosure clearance |
| Electrical | Contact map, data generation, rails, current, and grounding |
| Evidence | Material, compliance, and validation requirements |
| Commercial | Samples, production forecast, packaging, and delivery |
Return to the connector collection to compare SATA with other families, or send the device and interface drawing for review.



